Configure a plastic pipe extrusion line around your resin grade, diameter and wall requirements. ARKPM coordinates the extruder, tooling, sizing, cooling, haul-off and cutting or coiling scope to suit the pipe family you intend to produce.
A plastic pipe making machine proposal needs to describe the whole route to accepted pipe, including what happens after the die. ARKPM uses your drawing, resin grade and production priorities to configure extrusion, sizing, cooling, pulling and finishing as connected duties. Priority sizes and changeover products are reviewed separately so tooling and downstream adjustment remain clear. This page concerns production equipment; pipe materials, end-use standards and product qualification must be specified for your project. Output and dimensional commitments are established against the agreed resin, geometry, utilities and acceptance method.
Defined non-pressure pipe productsProtective conduit projectsOther pipe applications subject to product requirements and validationReview the material grade, melt behavior and pipe dimensions together. The die and extruder proposal should state the intended product range and any tooling changes required between sizes or formulations.
The calibration and cooling route must suit the pipe geometry and material. Review the available cooling-water conditions and tank arrangement before assuming a target line speed can be supported.
Coordinate pulling, cutting or coiling with the finished product. Contact arrangements, cut quality and handling should reflect the pipe condition at each stage and the way it is packed or transferred.
Pipe production brings the resin grade, tooling and downstream requirements into one process brief. Review barrel heating and temperature monitoring alongside that brief. The extrusion platform can be configured around the selected material, planned product range and access needed for service or changeovers.
An operator panel should reflect the equipment included in the pipe line. Discuss control access, displayed information, operating sequences and coordination with downstream stages. Panel layout and control scope can be customized around how operators prepare, run and change over the production line.
Provide drawings with diameter, wall and other critical dimensions, plus the resin grade and intended use. Identify which product is the main production case and which sizes are occasional changeovers.
Review extrusion output together with downstream limits and utility conditions. The agreed production case should describe stable, acceptable pipe after finishing, not just a throughput estimate at the extruder.
Specify where and when dimensions are measured and which additional product tests apply. Trial samples, retained settings and acceptance records should refer to the same drawing revision and material condition.
These are project inputs and configuration decisions. Performance is agreed against the material and product specification.
| Parameter | What to define |
|---|---|
| Pipe drawing and dimensions | Supply outer diameter, wall requirements, tolerances and the current drawing revision. Identify the main production size and the smaller-volume sizes that require changeovers. |
| Material specification | Provide the exact PE or PP grade and processing data. Other compounds or recycled-content plans need a separate review against the intended pipe application. |
| Output and production mix | State target saleable output, operating schedule and size-change frequency. Extruder output must be evaluated together with cooling, pulling and finishing limits. |
| Sizing and cooling | Review the calibration route, tank arrangement and available cooling-water conditions. Confirm site interfaces before fixing the downstream layout. |
| Cutting or coiling | Define finished lengths or coil format, acceptable cut condition and product removal. Match handling to the pipe condition after cooling and haul-off. |
| Acceptance and supply scope | Name the applicable product requirements and inspection methods. List tooling, equipment, controls, site services and trial responsibilities as included, optional or by others. |
Every ARKPM product family supports customization. These are the decisions that give the configuration its purpose.
All proposed equipment can be discussed around your product family. Separate essential launch sizes from future options so tooling, downstream adjustments and commercial scope remain clear and reviewable.
Discuss dimensional monitoring, recipe needs and interfaces to existing equipment. The measurement method and control response should be stated explicitly; an instrument by itself does not guarantee the finished product tolerance.
Adapt the proposed layout to available line length, handling direction and utility connections. Include finished-pipe removal and tooling-service access when reviewing whether the system fits your production area.
Share the information you have. Keep open questions visible so they can be resolved in the technical discussion.
Dimensioned pipe drawings and revision numbersResin grade and technical data sheetProduct use and applicable acceptance requirementsPriority sizes and desired production scheduleCooling-water data, power supply and floor planOnly a project-specific review can establish equipment suitability. Pressure applications also require the correct material, product standard, testing and approval route; purchasing equipment does not certify the finished pipe.
State the intended grade, source and proportion in the brief. Suitability depends on material consistency and end-use requirements, and must be assessed rather than inferred from the extrusion process.
The practical range depends on tooling, output, cooling and downstream adjustment. Share your actual product mix so required change parts and any separate configurations can be identified.
The supply schedule defines that boundary. A complete-line discussion includes tooling, sizing, cooling, haul-off and cutting or coiling as well as the extruder. Equipment already installed at your site can be listed separately so interfaces and responsibilities remain clear.
The resin, diameter and wall range, priority output, tooling set, cooling arrangement and finishing method shape the quotation. Controls, inspection requirements and site interfaces also matter. Send the drawing, resin data and product mix for a configuration-based quote.
Compare an extruder price with a complete production-line quotation, then define the tooling, downstream equipment, utilities and trial work your project needs.
Read the guide
Specify sizing, cooling, pulling and finishing around the product drawing, resin grade and accepted output, with clear responsibilities for site utilities.
Read the guidePrepare a recycling plant layout that includes feedstock storage, process interfaces, service access and utilities before approving equipment positions.
Read the guide
Translate a profile drawing into a custom equipment brief, with section-specific tooling, cooling support, haul-off and cutting planned around critical dimensions, visible surfaces and the intended production mix.
Explore this line
Specify tubing production equipment around bore, wall and resin requirements, with material preparation, sizing, cooling and take-up coordinated for the tube dimensions and delivery format your application needs.
Explore this lineShare your material, output requirements and site information for a project-specific proposal.
Request a line proposal
